- For ceramic and quarry tiles, mosaics, and natural stone
- For both moderately absorbent and non-absorbent tiles
- Joints widths: 2 - 10 mm
- Bright and intense colours
- Water and dirt repellent
- High mechanical strength and flexibility
- For interior and exterior use
- Provides an even and uniform surface
- Smooth consistency
Products
-
-
PlaneMix S40Pool and concrete repair mortar
-
PlaneMix 80Fast-track screeding mortar
-
PlaneMix 80 cementRapid setting cement for screeds
-
PlaneMix 100Fast-setting screeding mortar
-
PlaneMix 100 cementFast-setting screeding mortar
-
PlaneMixPrimerPrimer for Alfix PlaneMix levelling compounds
-
PlaneMixBinderAdmix for Planemix levelling compounds
-
-
-
TopCoat DesignUltra matt topcoat for levelled industrial looking floors
-
PlaneMix S8 rapidStand firm universal filler
-
PlaneMix 10Self-levelling and smoothing compound
-
PlaneMix S12 rapidSlump-free smoothing and repair mortar
-
PlaneMix 20Self-levelling and smoothing compound
-
PlaneMix 25 exteriorSelf-levelling and smoothing compound. Interior and exterior use
-
PlaneMix 30Self-levelling and smoothing compound
-
PlaneMix 50Self-levelling compound
-
PlaneMix 50 less dustDust reduced self-levelling compound
-
PlaneMix 60Self-levelling fibre-reinforced smoothing compound
-
PlaneMixPrimerPrimer for Alfix PlaneMix levelling compounds
-
PlaneMixBinderAdmix for Planemix levelling compounds
-
UniversalPrimerImproves adhesion in preparation for Alfix levelling compounds and tile adhesives on dense, non-absorbent substrates. Rollable consistency
-
Accessories for Alfix PlaneMix
-
-
-
ProFix PlusFlexible dust reduced tile adhesive
- Up to 1200 x 1200 mm -
ProFixFlexible tile adhesive - Light
-
LetFix less dustFlexible dust reduced tile adhesive - Light
-
LetFixFlexible tile adhesive - Light
-
LetFix UniversalFlexible tile adhesive - Light
-
CombiQuickFixRapid setting flexible tile adhesive
-
QuickFix premiumRapid-setting natural stone adhesive
-
FlexFixRapid-setting flexible natural stone adhesive
-
CombiFixFlexible tile adhesive
-
NormalFixTile adhesive
-
FlexBinder
-
UniversalPrimerImproves adhesion in preparation for Alfix levelling compounds and tile adhesives on dense, non-absorbent substrates. Rollable consistency
-
ReadyFlexReady mixed tile adhesive
-
C2 EpoxyAcid-resistant grout and tile adhesive
-
Thixotropic agentAdditive for Alfix C2 Epoxy
-
Montagelim1-component all-round mounting adhesive
-
-
-
FineFuge - CeraFill 5Fine grout
-
QuickFuge - Premium 8Rapid-setting natural stone grout
-
UniversalFuge - CeraFill 10Universal grout
-
IndustryFuge - CeraFill 18High-strength grout
-
RustiqFuge - CeraFill 20Wide joint grout
-
M-SiliconHighly elastic sealant
-
C2 EpoxyAcid-resistant grout and tile adhesive
-
Thixotropic agentAdditive for Alfix C2 Epoxy
-
EpoxyFuge 10252-component flexible, epoxy-based pool grout
-
Montagelim1-component all-round mounting adhesive
-
-
-
DuraPuds 615Water repellent plinth render
-
DuraPuds 650 rapidRapid-hardening repair and levelling render
-
DuraPuds 703Through coloured thin coat finishing mortar
-
DuraPuds 710Thin coat bonding mortar
-
DuraPuds 804Flexible, through-coloured thin coat finishing mortar
-
DuraPuds 810Flexible fibre render
-
DuraPuds 830Flexible facade adhesive - Light
-
DuraPuds 800 SRSilicone resin-based facade render
-
DuraDec 8000 SRSilicone resin-based facade paint
-
Accessories for DuraPuds
-
UniversalFuge - CeraFill 10
Product information
Product
Cement-based powder containing polymer modifiers. Added light stable pigments. Contains quartz sand with grain sizes up to 0.4 mm.
Coverage
0.5 - 1.5 kg per m² depending on tile size and joint width.
Packaging
Available in 5 kg and 20 kg PE lined paper bags
Unit | Colour | Item No. |
5 kg | White | 4505 |
5 kg | Grey | 4045 |
5 kg | Pale grey | 4515 |
5 kg |
Manhattan Steelgrey |
4525 |
5 kg | Graphite | 4535 |
5 kg | Anthracite grey | 4565 |
5 kg | Black grey | 4545 |
5 kg | Light beige | 4555 |
Unit | Colour | Item No. |
20 kg | White | 4501 |
20 kg | Grey | 4041 |
20 kg | Pale grey | 4511 |
20 kg | Manhattan Steelgrey | 4521 |
20 kg | Graphite | 4531 |
20 kg | Anthracite grey | 4561 |
20 kg | Black grey | 4541 |
20 kg | Light beige | 4551 |
Tests
DS/EN 13888
Technical data
- Working temperature
- +5°C - +25°C
- Density
- 2.0 kg/litre (mixed with water)
- Working time
- 1 - 2 hours at +20°C
- Foot traffic
- After 24 hours vid +20°C
- Full strength
- After 14 days at +20°C
- Classification - DS/EN 13888
- CG 2 W A, high class
- Shelf life
- Min. 12 months in unopened bags
Technical enquiries
Folderen: “Fliser og fuger – Rengøring og pleje med Alfix”
Alfix Rense/plejemiddelserie
Produktinfo for:
Alfix FineFuge - CeraFill 5
Alfix QuickFuge Premium 8
Alfix IndustryFuge - CeraFill 18
Alfix RustiqFuge - CeraFill 20
Alfix Syr a’
Sikkerhedsdatablad
General information
For moderately absorbent and non-absorbent ceramic and quarry tiles, mosaics, and natural stone.
Grouting can usually be made 48 hours after tiling has been completed. Joints should be clean, dry, free
from dust and loose particles from adhesive and bedding mortar Joint depth should appear uniform.
For grouting of certain types of receptive tiles, such as matt glazed or porous tiles, stains and excess grout can be very difficult to remove. In case of doubt, it is recommendable to do a trial application on a limited and less visible area to ascertain resistance.
Switch off any underfloor heating 3 days before tiling and do not re-connect until 14 days after completion.
Underfloor heating, ventilation, waste heat recovery systems, dehumidifiers, etc should be switched off during tiling. Deactivate all installations 72 hours prior to grouting and reactivate 14 days after completion of work at the earliest. Underfloor heating temperature increase should be by 5°C per 24 hours until preferred surface temperature is obtained.
Inlet temperature should be max. +35°C
Final appearance
Finished joints should be evenly filled and the colour should appear uniform.
The following conditions may affect the natural properties of the cement and cause colour differences:
-
Early cleaning with wet sponge may lighten the colour. This phenomenon is most likely to occur in case of dark colours.
Remedy: Clean off with acidic cleaner, such as Alfix Acid Wash. -
Rapid drying may brighten the colour and produce a weak joint.
Remedy:Keep the surface damp for optimum hydration of the grout. Wet with damp sponge. -
Repairs or visible seams after working breaks may cause colour differences.
Remedy: Remove the joints mechanically and re-grout the area. Wipe over and clean off the tiles several times with slightly damp sponge. -
Moist from substrate and uneven absorption from tile edges may cause a locally darker colour. Remedy:Wash the area several times with a mixture of soap flakes and water.
Colours
Available in white, grey (unpigmented), pale grey, Manhattan steel grey, graphite, anthracite, black grey, and light beige. Colour swatches available on request.
Application
How to use
Add 0.20 – 0.24 litre clean, cold water per kg powder. Pour the water into a clean container and add the powder while stirring thoroughly with mixing drill. Keep stirring until the consistency is completely uniform, smooth, and lump-free. Allow the mixture to rest for a few minutes and stir briefly before use.
Apply Alfix Universal grout to the surface with a soft rubber squeegee while working diagonally over the joints ensuring that they are compacted and completely filled. Remove excess grout immediately while working.
When the grout begins to set, within 1 hour, slurry off the area using wet sponge frequently rinsed in clean water. Wipe over tiles in broad, diagonal sweeps until joints appear even and filled. Finally, clean off and finish tiles and joints with only slightly damp sponge.
Note!
Premature cleaning with wet sponge or the exposure to varying site conditions, such as heat, draught or ventilation, may affect the natural properties of the cement and cause discolouration or damage to the grouted joint.
Any remaining grout film on the surface can usually be removed after 12 – 24 hours using a mild vinegar/water mixture. To remove more stubborn grout film or efflorescence, use Alfix Acid Wash.
Note that the temperature of mixing water will influence setting time. Higher room and water temperature will shorten time.
Protect the joints from heat, draught, and other climatic conditions which will affect drying.
Do not cover areas just grouted with plastic foil or sheets, and avoid leaving small pools of water in the joints during the first 3-4 days
Cleaning
Grout residues on tiles and tools should be removed with water before the mix begins to set. Cement-based products harden when mixed with water, hence do not pour surplus adhesive into the drain system.
Downloads